Jump to content

Welcome to 4GTuner
Register now to gain access to all of our features. Once registered and logged in, you will be able to create topics, post replies to existing threads, give reputation to your fellow members, get your own private messenger, post status updates, manage your profile and so much more. If you already have an account, login here - otherwise create an account for free today!
Photo

VR4 Aluminum Radiators

- - - - -

  • Please log in to reply
9 replies to this topic

#1
RocksolidGVR4

RocksolidGVR4

    Advanced Member

  • Active Members
  • PipPipPip
  • 167 posts
  • LocationPerth
I was working on the Galant today redoing the engine harness due to the wires being brittle and some plugs were damaged. I've ended up cutting the harness off from the firewall, put a plug on and redone the section of harness that runs over the intake to all the injectors/CAS/TCS etc I'll post some pics if I finish it tomorrow.

Anyway back to my question, while I was working on the harness I was looking at the radiator fan and thinking that theirs stuff all room between the fan and turbo intake. So what I want to do is change the fan to a slim style and also upgrade to a aluminum radiator.

What setup are people running out their and what would you recommend?

Thanks

#2
croket

croket

    Advanced Member

  • Active Members
  • PipPipPip
  • 734 posts
  • Locationwestern australia
Mine is running a bigger alloy radiator and there was no notable decrease in water temp on the logger from the stock radiator. It does look cool though , you could always delete aircon and run a push type fan in front of radiator

#3
croket

croket

    Advanced Member

  • Active Members
  • PipPipPip
  • 734 posts
  • Locationwestern australia
Im also using stock shroud with some of it cut out to fit , and its a damn tight awkward fit too

#4
JayRome

JayRome

    Blurring the line between 1st to 3rd Gen engines....

  • Active Members
  • PipPipPip
  • 4,958 posts
  • LocationMelbourne

When you run a alloy rad, it's actually thicker then stock unit. So the fan will get closer to your turbo, but the plastic thermo fan will help with space. 


Chosen Weapons:
WideBody Galant GSR 4g63 N/A+T Hybrid 1st/3rd gen +AWD
Audi A3 slow POS


#5
blackvr

blackvr

    Advanced Member

  • Active Members
  • PipPipPip
  • 574 posts
  • LocationAdelaide

The alloy radiators tend to suit Evo 3 etc, but fit fine with a little bit of fiddling. They are very cheap, and as Jayrome found, they are thicker... but work fine still with an aftermarket slimline thermo fan.  



#6
croket

croket

    Advanced Member

  • Active Members
  • PipPipPip
  • 734 posts
  • Locationwestern australia

When you run a alloy rad, it's actually thicker then stock unit. So the fan will get closer to your turbo, but the plastic thermo fan will help with space. 

 

You should make me a rad like your mate so it sits under rad support sooo much more room , wish i was as handy with the welder as your are !!!



#7
MDK87

MDK87

    Hyundai's can't fly!!

  • Active Members
  • PipPipPip
  • 2,364 posts
  • LocationBrisbane

I was working on the Galant today redoing the engine harness due to the wires being brittle and some plugs were damaged. I've ended up cutting the harness off from the firewall, put a plug on and redone the section of harness that runs over the intake to all the injectors/CAS/TCS etc I'll post some pics if I finish it tomorrow.

 

Hey buddy you picked the words right out of my mouth.

I intend on doing the same thing. Where did you go to buy those 4-way rectangle connectors for the CAS/TPS? Are there any other special plugs that you need when doing this? I already have the quick release EV-1 injector connectors. What about the temp sensor connector that is screwed into the thermostat housing?

This looks pretty similar - http://www.ebay.com....2fd703eb&_uhb=1

 

I intend on replacing all of my crusty old wiring as well.

Btw yeah unless you delete the AC the benefit of slimline thermo is kinda outweighed by the thickness of the alloy radiators like these ^ guys are saying. I think with a decent slimline fan you might end up ~ 10-20mm better off overall.



#8
dakiller

dakiller

    Advanced Member

  • Members
  • PipPipPip
  • 64 posts
  • LocationMelbourne

Where did you go to buy those 4-way rectangle connectors for the CAS/TPS? Are there any other special plugs that you need when doing this? I already have the quick release EV-1 injector connectors. What about the temp sensor connector that is screwed into the thermostat housing?

 

http://www.jnztuning...h=21_32_153_731



#9
RocksolidGVR4

RocksolidGVR4

    Advanced Member

  • Active Members
  • PipPipPip
  • 167 posts
  • LocationPerth
I brought a connector kit from Sheridan Engineering website, ended up costing me $116.00 landed to my door which wasn't to bad I guess altho I didn't need all the connector in the kit. As for the the sensor on the thermostat housing my plug is still ok and their are some small pins on the kit which I hope will fit, haven't tried yet.

Here's some pictures of what I have done, I've decided to run all the wires for the engine through the one but kept the exhaust temp wires separate in its own harness. Still need to neater it up once I get the engine back together.
20140701_185009.jpg
20140701_171032.jpg

Back to the radiators, I might invest in a slim line fan for my standard radiator for now and do some research into alloy rads.

Thanks for the advice so far.

#10
JayRome

JayRome

    Blurring the line between 1st to 3rd Gen engines....

  • Active Members
  • PipPipPip
  • 4,958 posts
  • LocationMelbourne

If you look around wreckers, you can get stock Mitsu fans that can be slimmer then an off the shelf "slim line fan"...

 

Remade this stock fan to fit a CB lancer with a decent size turbo and 50mm Evo1-3 alloy rad. Plenty of space,..

 

IMAG1073_1.jpg


Edited by JayRome, 01 July 2014 - 03:54 PM.

Chosen Weapons:
WideBody Galant GSR 4g63 N/A+T Hybrid 1st/3rd gen +AWD
Audi A3 slow POS



1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users